Difference between revisions of "Rebuilding the petcock/fuel tap"
Revision as of 23:44, 28 March 2019
Have any of these happened to you?
This likely means you need to rebuild your petcock. There are several options for doing this:
This illustration shows how everything goes together on the petcock.
What you decide to do will likely depend on whether you can diagnose which part of the petcock is damaged. This will, of course, involve taking it apart and looking at it before you order parts. This is the cheapest way, but you'll have to wait for parts.
If you want to order parts from your dealer or one of the OEM online sources, here is what you'll need:
There is a rebuild kit from K&L Supply, part #18-2723, but it is for the E series (86-87) bikes. It doesn't have the correct diaphragm for the later F (88-07) bikes. All the other parts are the right ones, but if your diaphragm is bad, plan on spending another $25 on top of the $25 for this kit.
K&L Supply part numbers:
Checking the vent
For the diaphragm to work properly, there is a small vent hole to atmosphere on the bottom side of the petcock. This has to be clear. After you disassemble the petcock, check for crud on both sides of the diaphragm. If you're very fortunate, this may be all that is wrong. If there is debris on the fuel side, then a check of the complete fuel system would be prudent.
Remove the 5 screws on the back side. Be careful when you open it, since there is a small spring inside.
The diaphragm has two flaps and goes through the plastic spacer. If you are not going to replace it, just leave it alone. You can take it out of the plastic spacer, but be careful when you do. Take note of the small hump on the plastic piece so you put it back together the right way. Notice how the pointed part is not even on both sides.
Remove the o-ring from the new diaphragm and swap it with the one on yours, or replace it with a new one if you didn't buy a kit.
Remove the two screws on the lever side and take the face plate off. There is a pressure fit washer between the face and the lever body. It's supposed to be wavy; don't try to straighten it out.
The lever body pulls straight out. You might feel some resistance, since there is an o-ring on it. Once you have it out, take the o-ring off.
Remove the black lever gasket (has 4 holes – called 'packing' in the parts diagrams). This is usually one of the first things to cause leaky petcocks. You can buy it by itself for roughly $3, but if you're going to take the whole thing apart you might as well replace the other o-rings, too.
This one was a little chewed on.
Now that you have all the pieces off, take some carb cleaner and a small brush and clean everything. This one had some buildup on the side where the small o-ring on the diaphragm meets the petcock. Don't be too harsh when cleaning. Let the cleaner do most of the work.
Make sure everything is nice and clean. Replace the o-rings on the diaphragm and lever body, then reassemble. Put some grease on the spring washer and valve plate when putting it back together (see photo).
You should now have a clean, leak-free petcock. The kit comes with a new o-ring for the petcock-to-gas tank connection as well.
You should probably change your oil now, before you start it up. If the petcock has been leaking into the oil, not only will you have too much oil, what's in there will be thinned out and much less effective. You don't want to replace major engine components just because of that.
Rebuilding Vs New
If your petcock is shot, save your time, and money and get a new one, the cost of rebuilding it isn't much cheaper, due to you need two separate kits, as they for some reason don't make just one.
New one cost about $65.00
Also be sure to order the orings(92022-183 WASHER,6.2X11X1.5)and new bolts(92001-1091BOLT,6X20),trust me you'll be better off in the long run.
Rebuilding kits are about $60 total.
K&L Supply Diaphragm Only for Fuel Petcock Repair Kit 18-6638 https://www.amazon.com/dp/B0055DWO60/ref=cm_sw_r_awd_s1CGub1W9N3PH
K&L Supply Fuel Petcock Repair Kit 18-2723 https://www.amazon.com/dp/B001KO2JRW/ref=cm_sw_r_awd_U1CGub05DT5NT
IMHO not worth it rebuilding, also be sure to check vacuum and fuel lines for wear, holes, and cracks, if in doubt replace them. Also replace the two small O-rings on the bolts for the petcock part# 92022.
This is the time to add an inline filter filter, if you don't have one already.
K&N 81-0221 Fuel Filter https://www.amazon.com/dp/B000E2AR70/ref=cm_sw_r_other_awd_ncMwwbE333H0E
UPDATE by Ghostt: K&L SUPPLY now makes a complete kit for 88-07 models, according to their own 2016 catalog, Part # 18-2702.