Difference between revisions of "How do I change the brake fluid?"

From Ninja250Wiki
Jump to: navigation, search
(Procedure)
m (Stuff you need to know)
Line 6: Line 6:
 
If your rubber brake lines are four years old or more, it's time to change them to [[Stainless steel brake lines upgrade|stainless steel lines]] anyway, so you might as well do that. It'll save you having to replace the fluid twice.  
 
If your rubber brake lines are four years old or more, it's time to change them to [[Stainless steel brake lines upgrade|stainless steel lines]] anyway, so you might as well do that. It'll save you having to replace the fluid twice.  
  
Brake fluid is hygroscopic, which means that it tends to absorb any water it encounters (usually from the air). Water which contacts brake system components will tend to corrode it. Watery/old brake fluid also boils at a lower temperature, which is very dangerous in emergency stops, where a great deal of heat can be generated in the brake system. Boiling brake fluid creates pockets of vapor, which drastically reduces your ability to transmit pressure to the brakes.  
+
Brake fluid is {{wikipedia|hygroscopic}}, which means that it tends to absorb any water it encounters (usually from the air). Water which contacts brake system components will tend to corrode it. Watery/old brake fluid also boils at a lower temperature, which is very dangerous in emergency stops, where a great deal of heat can be generated in the brake system. Boiling brake fluid creates pockets of vapor, which drastically reduces your ability to transmit pressure to the brakes.  
  
 
For these reasons, brake fluid needs to be changed about every 2 years. As brake fluid absorbs water, it gets darker, so if your brake fluid looks dark (tan or brown), it needs to be changed. New DOT4 brake fluid is nearly clear, with a slight amber hue, although different brands and even batches will have differences in color.  
 
For these reasons, brake fluid needs to be changed about every 2 years. As brake fluid absorbs water, it gets darker, so if your brake fluid looks dark (tan or brown), it needs to be changed. New DOT4 brake fluid is nearly clear, with a slight amber hue, although different brands and even batches will have differences in color.  

Revision as of 19:13, 2 January 2011

Stuff you need to know

You may get some more tips from the brake bleeding article.

If your rubber brake lines are four years old or more, it's time to change them to stainless steel lines anyway, so you might as well do that. It'll save you having to replace the fluid twice.

Brake fluid is hygroscopic, which means that it tends to absorb any water it encounters (usually from the air). Water which contacts brake system components will tend to corrode it. Watery/old brake fluid also boils at a lower temperature, which is very dangerous in emergency stops, where a great deal of heat can be generated in the brake system. Boiling brake fluid creates pockets of vapor, which drastically reduces your ability to transmit pressure to the brakes.

For these reasons, brake fluid needs to be changed about every 2 years. As brake fluid absorbs water, it gets darker, so if your brake fluid looks dark (tan or brown), it needs to be changed. New DOT4 brake fluid is nearly clear, with a slight amber hue, although different brands and even batches will have differences in color.

Dirty:

Dirtyfluid.jpg

Clean:

Cleanfluid.jpg

Or you can follow Wes's E-Z guide to brake fluid color:

  • Clear = OK
  • American Beer = Change this year
  • Molson Canadian = Change this month
  • Harp = Change this week
  • Smithwick's = Change today
  • Guinness = Change yesterday

Brake fluid is corrosive to painted surfaces and will damage the paint in short order. If you spill any on your bike, wipe it up quickly. DO NOT spill any brake fluid on the brake disc or pads. If you do, use brake cleaner to clean the disc, and replace the pads. Any brake fluid (or any other fluids) on the ground can be cleaned up by sprinkling kitty litter on it.

Tools & supplies

  • unopened, fresh bottle of DOT4 brake fluid (8-12 oz will normally do both brakes)
  • 3 ft of clear, 3/16" inside diameter vinyl hose
  • open-end wrench to fit the bleed nipple
  • phillips-head screwdriver
  • sealable plastic or glass container (milk or Snapple bottle)
  • a few old rags

What kind of brake fluid?

DOT 4 fluid has a slightly higher boiling point than the older DOT 3 specification. Find a quality brand of DOT 4, such as Valvoline Synthetic DOT 3&4.

Don't use DOT 5. It is completely not compatible with your brake system and could cause MASSIVE FAILURE. You can't even drain the DOT 4 and then put in DOT 5, as the seals/lines will fail. There's no reason to, anyway. DOT disc brake bikes don't usually need high temp brake fluid (like DOT 5) for a couple of reasons.

  • The ratio of brake size to vehicle mass means that the brakes aren't really working that hard compared to a car.
  • Even when they are being used heavily, the calipers and rotors are directly in the flow of cooling air. Not only that, the hoses, lines, and master cylinder are exposed to the air.

If you're racing a bike, go ahead and get the highest temp fluid you can afford. But for street bikes, just use the Valvoline Synthetic.

Procedure

All you need to change your brake fluid are a screwdriver for opening the reservoir, an open-end wrench for the bleed nut, a length of hose, and some catch container (glass, such as a Snapple bottle). Once the reservoir is cleaned of the old fluid and refilled, just squeeze the lever, open the bleed nut until the brake lever hits the grip, tighten the bleed nut and release the lever. Repeat as necessary.

Put the bike on the centerstand, attach the hose to the front bleeder valve, and run the length of hose into the empty bottle.

Bleedvalvecloseup.jpg

Carefully clean the reservoir cap to prevent getting any dirt in the system. Then, unscrew and remove the reservoir cap on the right handlebar, and remove the secondary cap and rubber seal; remove as much old fluid as you can by sopping it out with a paper towel. Then, fill the reservoir with new brake fluid and place the cap back on, to avoid splashing. To swap the brake fluid, you must repeat the following sequence several times:

  • open the bleeder valve
  • squeeze the brake lever
  • close the bleeder valve
  • release the brake lever
  • check the reservoir and fill if it's below 1/3 full
  • Remember: Don't release the brake lever while the bleeder valve is open (it'll introduce air into the system.)

Keep doing this until the fluid coming into the catch bottle is the color of the new fluid. Once the color changes, you've successfully swapped out the brake fluid. When you're in the midst of bleeding, don't overtorque the bleeder valve as you close it - just close it hard enough to stop fluid from flowing.

Keep going until the brake control feels firm and solid. The brake control should not sink at all and should come to a stopping point and stay there, no matter how long you hold it. If you can't get to this point, follow the instructions on bleeding the brakes.

Tightly seal the reservoir cap and bleeder valve to deter air entry. Torque for the bleeder valve is 69 in-lbs. Take it for a slow test ride, and if everything is good repeat for the rear brake (the rear system is smaller and will probably take less time than the front). You should notice improved lever/pedal feel, and your stopping distances should decrease as well.